1．適用范圍（Available range）: 本高壓保險絲適用于微波爐。 This fuse is suitable for micro-wave ovens. 

2.型號定義解釋（Model meaning）： 13FV：快斷系列產品 （13FV：Quick－Acting） 

3．相關標準（Safety Standards）:GB9364 IEC60127 通過認證（Approved file No.）： 

4．尺寸與結構(Size and construction): 4.1 外形、結構及尺寸(The out view, construction and dimensions): 參考下圖 Refer to the following Drawing

5．電氣特性(Electrical performance) 

5.1 測試條件(Testing Ambient) 測試條件都應在下列大氣條件下進行： All tests should be carried out under the following conditions： -溫度(Surrounding temperature)：15℃～35℃; -相對濕度(Relative humidity)：45%～75%； -大氣壓力(Atmosphere pressure)：8.6x10 4 Pa～1.06x10 5 6.2 時間/電流特性(Time-Current Characteristic)

5.2時間/電流特性(Time-Current Characteristic)

5.3 承載電流能力(Carrying current capacity) 23±1℃時，通以1.1倍額定電流4小時，熔斷器不熔斷； 23±1℃degrees,with 1.1 times the rated current for 4h ours,the insurance tube fuse 

5.4 耐久性試驗(Endurance test) 1）對保險絲通過 1.05 倍額定電流 1 小時，然后切斷 15 分鐘，重復此循環 100 次。 A current 1.05 In is passed through the fuse-link for a period of 1h.The current is then switched off for a period of 15 min.The cycle is repeated 100 times. 2）然后對熔斷體通以 1.15 倍額定電流 1 小時。 A current 1.15In is then passed through the fuse-link for 1h. 3）測量熔斷體兩端的電壓降，試驗后，熔斷體兩端的電壓降的增大量不大于試驗 前測得值的 10%。 Finally,the voltage drop across the fuse-link is measured.The voltage drop across the fuse-link after the test shall not have increased by more than 10% of the value measured before the test. 4）試驗后，標記仍應清晰可辨，而且諸如端帽上的焊點不應出現任何明顯的劣變。 After the test,the marking shall still be legible and soldered joints on end caps,for example,shall not show and appreciable deterioration. 

5.5 溫升 Temperature rising 在 23±1℃條件下，通以 1.1 倍額定電流，達到熱平衡后，高保殼體**的溫 升＜60K，端蓋溫升＜85K。 After the fuse is through 1.1-times rated current under the condition of 23±1℃ to reach a heat balance, the temperature rising of glass tube center is ＜ 60K, the temperature rising of terminal cover is＜85K. 

5.6 冷熱沖擊試驗 Temperature shock test 熔斷器于 85±2℃/3h，-25±2℃/3h 為一循環周期，重復 5 次，熔斷器不得有斷， 表面不應有裂紋等其它缺陷，并符合導線強度要求。 High voltage shall be at 85+2℃/3H;-25+2℃/3H for one week,repeat 5 times; The surface shall n ot have the other defects such as cracks and be complied with the requirements of lead wire streng th and vibration test. 

5.7 分?jǐn)嗄芰?/span>(Breaking capacity) 1）每一次測試，保險管能安全動作，不能出現以下現象： In each of the tests, the fuse-link shall operate satisfactorily without any of the following phenomena: -持續電弧; -permanent arcing; -引燃; -ignition; -保險管**; -Bursting of the fuse-link.

6.安全測試(Safety test) 1) 高壓擊穿試驗(High-voltage breakdown test) 熔斷后的保險絲,在保險絲兩端加 8KVAC 保持 1 分鐘都不會出現擊穿現象。 8KVAC shall be applied at both end of the fuse for 1 minute, the fuse after breaking shall not be breakdown. 2) 絕緣電阻(Insulation resistance) 測試絕緣電阻應≥100MΩ（500VDC） Test of insulation resistance should be greater than or equal to≥100MΩ(500VDC). 3) 端子與外殼間 8KVAC/3S/5mA，無擊穿閃絡。 8KVAC/3S/5mA between terminal and outside case shall no breakdown and flicker. -55 -35 -15 5 25 45 65 85 105 125 120% 110% 100% 90% 80% 70% 60% 50% 23℃ 環境溫度(℃) Ambient Temperature(℃) 額 定 值 百 分 比 P e r c e n t R a tin g 4) 耐濕熱 Withstand humidity heat 溫度 43±3℃,相對濕度 90%±2%,放置 48 小時后,滿足耐壓要求，絕緣電阻 >100MΩ(DC 500V)。 The temperature is 43±3℃, the relative humidify is 90%±2% and after putting 48 hours, it shall be satisfied the requirements of withstand voltage, the insulated resistor is >100MΩ (DC 500V). 85) 灼熱絲試驗（針焰試驗）Scorching hot wire test (needle-type flame test) 750℃，不起燃，或起燃小于 2 秒; 850℃，在 30 秒內熄滅; 750℃, non-combustible, or less than 2 seconds of ignition; 850 ° C, extinguished in 30 seconds;  6) 耐漏電起痕 Withstand leakage scar 在 175VAC 下，用 A 溶液測試 50 滴，不應起火或泄漏電流≥0.5A 持續 2S。 Under 175VAC，it will be tested 50 drops using solution A，and shall not catch a fire or leakage current is more than 0.5 A and last 2 seconds  7) 阻燃 Anti-combustion 外殼阻燃等級為 VO 級（離焰后持燃時間小于 30 秒）。 The class of shell anti-combustion is V0 class (the flame duration is less than 30 seconds after leaving the flame)